The flexible one
Whether freestanding or in a shaft, on a parapet or with an opening in the floor, with a door or as a front-and-rear-opening lift: It fits.
the most common variants...
Get a free offer for your column lift in two steps. You are welcome to note any adjustments (e.g. a different payload or different dimensions) in the 'Change requests' field.
| Payload: | 1.000 | kg |
| Width: | 1.500 | mm |
| Length: | 2.400 | mm |
| Effective Stroke: | 1.320 | mm |
| Payload: | 1.000 | kg |
| Width: | 1.000 | mm |
| Length: | 1.500 | mm |
| Effective Stroke: | 4.300 | mm |
| Payload: | 1.000 | kg |
| Width: | 1.500 | mm |
| Length: | 2.400 | mm |
| Effective Stroke: | 1.320 | mm |
| Payload: | by request |
| Width: | by request |
| Length: | by request |
| Effective Stroke: | by request |
The effective stroke is not dependent on the platform
In the case of a lift table, there must be space for the scissors underneath the platform. To reach high lifting heights with small platform dimensions, a lift table with multiple scissors is needed. One example would be our double-scissor lift table.
With a column lift , however, the platform size does not determine the effective stroke as the lifting mechanism is positioned next to the platform. This means that you select the desired dimensions for your loading platform without having to pay attention to the required effective stroke.
[up]
Can also be used without a pit
If there is a pit for the column lift, we can install the platform flush with the floor so that you do not have to negotiate a slope when loading and unloading.
However, if you do not want a pit or if a pit is not feasible, we have the matching solution for this too. We offer ramps that are individually tailored to your column lift. There are two variants available to negotiate a slope: Ramps with a flat slope for electric high-lift stackers or ramp plates for a small space.
[up]
Accessories customised for you
In addition to the ramp plates or access ramps just mentioned, we also have other extras ready for our column lift. For example, what if you don’t want build a shaft from bricks? Then we supply you with a shaft made of sandwich panels or a suitable landing enclosure. Of course, including installation. Or do you need an automatic control instead of a dead man’s control? Simply tell us what you need so that we can provide you with the matching offer.
[up]
Deciding on your column lift
When reviewing an offer, the same questions always arise: Is that the column lift or goods liftthat I need? Is it the right fit for my installation situation, for example, as underground lift?
We believe in the well-known saying to make sure that it does: A picture is worth a thousand words. After placing the order, you will receive a drawing for approval from us with all the key points of your order: from the actual column lift to the extras to the installation situation.
[up]
All from a single source
We like to have everything under control. That is the reason why we take care of all phases of production for you: from the first consultation to the design and structural steel engineering to the installation of the column lift at your site. The advantage for you: You have a point of contact with the necessary expertise for all your questions.
[up]
Frequently asked questions & our answers ...
Where is the headquarters of Janzen Lifttechnik GmbH?
We are at home in the rural Emsland, more precisely in Niederlangen a part of the Lathen municipality directly on the A31 motorway. This means that we are roughly halfway between North Rhine-Westphalia and the North Sea, right on the Dutch border.
Our region is known, among other things, for the various nature reserves, the well-developed cycle paths, the manufacture of cruise ships, as well as the headquarters of various distilleries.
Should you ever come to our region, we look forward to a visit in our Plant.
Where are the lifting tables and elevators produced?
With us, not only does the final assembly take place in Germany, but we also cover the entire production chain from construction through steel construction to final assembly in our plant in Niederlangen. With us you get a real 'Made in Germany'.
Is the offer aimed only at traders or also at private individuals?
Even if our products are mainly used in an industrial environment, we naturally also offer them to private individuals.
Just give us a call or send us an inquiry and we will be happy to contact you.
Will I receive a drawing before production starts?
In any case. To ensure that you get the product that you really want, we provide you with an approval drawing before production begins. In addition to the actual product, this also includes the installation situation. As the saying goes, a picture is worth a thousand words.
Can I get a CAD model?
You can receive a (greatly) simplified CAD model of our standard products before ordering. After the order and the construction phase, we can also provide you with CAD models of the individual special lifting tables. A data exchange is possible in all common formats (.stp, .dxf, .dwg etc.).
Where can you deliver to?
We produce our lifting tables and column jacks in accordance with European standards and guidelines. Accordingly, our sales area is limited to all countries that recognize these standards and guidelines (e.g. the members of the European Union, Switzerland and Australia).
Is it possible to assemble in the same area?
On request, we assemble our systems throughout Germany, as well as in the neighboring countries of Germany.
